My Manufactured Home Guide

Triple wide installation

What does it take to install a triple wide mobile home in North Carolina?

More than a double wide, in every step. A triple wide comes from the factory as three sections, each its own oversize load on the road, and the crew joins three sections on site instead of two.

Short answer: Plan four things before you buy: a road and driveway that three long loads can get down, a pad big enough to set three sections and turn the truck, a septic permit sized for the bedroom count, and a setup crew that has set multi-section homes before. Ask the crew in writing what they include.

Reviewed by a manufactured home setup contractor and dealer.

Tell me about your project. The quote is free.

I'll call you to learn about your project, then give you one price in writing for the work.

Phone or email — I need one to reach you
What do you need? Tap any that apply (optional).

You'll hear directly from me — the same person from the quote to the keys.

Prefer to talk?Call now8 AM–8 PM

What to check first

Start with the exact property, quote, record, or job detail behind your question. Mark what is confirmed, what still needs a current source, and who must answer it. Use the checklist to keep the next call, document, or decision clear.

The width and length of each of the three sections, from the dealer

The road and driveway: width, turns, low wires, trees, soft ground

The pad: room to set three sections and back the truck out

The septic permit: does it match the bedroom count of this home?

The setup quote: piers, both marriage lines, anchoring and close-up listed line by line

Step 1

Get each section's size from the dealer before you sign for the home.

Step 2

Walk the route from the road to the pad with the setup contractor.

Step 3

Check the septic permit and the electrical service against this home, not an older one.

Details to Sort

The checks that usually matter before you commit money.

Three loads, not one

Each section travels as its own oversize load, so the transport company plans three moves and the permits for each. A driveway that takes a double wide can still stop a triple wide on a tight turn or a soft shoulder. Have the transporter look at the route before the home is ordered, not the week it ships.

Two marriage lines on the foundation

Where two sections meet is a marriage line, and a triple wide has two. Each one carries its own row of piers under it, so the foundation plan has more supports than a double wide of the same length. The home's installation manual sets the pier spacing; ask the setup crew to show you where they took their numbers from.

Bigger home, bigger septic and power

In North Carolina the septic permit is sized by bedrooms. A triple wide often has more bedrooms than the home the land was first permitted for, so check the improvement permit before you buy. The same goes for power: ask the electrician whether the service at the pole is large enough for this home.

Close-up is where quotes differ most

Joining three sections means two seams to close inside and out: the roof, the floor, the walls and the trim along both marriage lines. Some setup quotes include it and some leave it to a trim-out crew. Put the close-up line on every quote you compare.

Tell us the job and where the home is. I'll call you, then give you one price in writing for the job.

Secondary Support

Need more help understanding your situation?

Not sure what work you need? Call now (8 AM–8 PM) or send the request: the quote is free, and the person who quotes your project runs it.

Free quote

Ask about transport and setup

Share a few details to get an immediate starting point, likely next steps, useful guides, and relevant contractor categories. You do not need to know the exact permit or contractor type yet.

Add more project details (optional)

These details can help, but you can leave this closed if you are not sure yet.

Prefer to talk?Call now8 AM–8 PM

Common questions

Is a triple wide set up differently from a double wide?

The steps are the same, but there are three sections to place and join instead of two. That means two marriage lines, more piers and more close-up work. Hire a crew that has set multi-section homes.

Can any lot take a triple wide?

No. The road, the driveway and the pad have to take three long loads and room to set them. Zoning can also limit the size or class of home allowed, so check the land before you buy the home.

Does a triple wide need a bigger septic system?

Often. North Carolina sizes septic permits by the number of bedrooms. If the home has more bedrooms than the permit allows, the permit has to be changed before the home is set.

Who joins the three sections together?

The setup contractor sets the sections on the piers and joins them. The inside and outside close-up along the seams is sometimes theirs and sometimes a trim-out crew's. Ask who does it in writing.

Who can set up a triple wide in North Carolina?

Use the free request on this page. Tell us the home and where it is going. I'll call you, then quote your setup who does mobile-home work in your county.

Call now· 8 AM–8 PM